Build project

This browser keeps one draft. Save an editable project to continue on another device, or download a build record to share.

Orthographic CAD & Center-of-Mass Check

Dashed yellow box = 150 × 150 mm limit. Crosshair (⊕) = combined center of mass; keep it inside the green wheelbase stability zone.

Constraint check

Slicer Layer & Toolpath Preview

Left: build plate elevation & layer lines up to the scrub bar. Right: cross-section toolpath (blue walls, yellow infill) & hole bridge behavior.

Workflow note: Use the slicer approved for the classroom printer. Cura is one slicer; MakerBot printers may use MakerBot Print or CloudPrint instead. Never assume one brand’s profile transfers safely to another printer.

Choose settings for a structural prototype

Hand-Extruded Bracket Deflection Bench

Watch how sideways force bends the vertical sensor post and tilts the ultrasonic sight cone away from horizontal.

Where should the plastic go?

A thick lump can still fail at one narrow seam. Select a joint and compare its resistance to a sideways push.

Joint stiffness & load limit Butt seam (Weak)
Live Gear Mesh & Ramp Climb Dynamometer

Left: driver (blue) and driven (yellow) spur gears turning at live ratio. Right: ramp climb demand vs. net output torque after ~15% mesh friction.

Gear ratio & load match

Output torque capacity 3.00× ratio (Climbs)
Servo Horn Sweep, Hard Stops & Load Moment

Center at 90° before pressing the horn onto the spline. Red sectors show mechanical collision stops (≤ 20° and ≥ 160°).

Position & torque budget

Staged Bring-Up & Fault Isolation Simulator

Check off bring-up gates or inject a common bench symptom to practice isolating the fault without tearing the whole robot apart.

Bring-up status & fault drill

Bring-up progress 4 of 8 gates passed

Debug rule: If a known test stops passing, disconnect the newest subsystem and restore the last known-good state. Do not replace several parts at once.

100 mm Ping-Pong Ball 3-Trial Arena

Three trials include small real-world heading jitter (±4 mm) around your lateral alignment offset.

Tool geometry & alignment

Engineering summary builder

Draft—edit this in your own voice

Subsystem Configured Spec Status / Evidence

Engineering · Robotics · Fabrication

Robot Build Studio

Carry one robot from measured chassis to tested tool. Every mission ends with evidence that the next team can inspect: a dimension, prediction, test result, photograph, or design decision.

Grades 7–12 Eight class missions Teams of 2–4 CAD + fabrication + electronics
Back to Engineering lessons

One build, eight decisions

Do the missions in order when building a complete robot, or open one as a standalone workshop. Keep one engineering notebook throughout. Before changing a design, write what you expect the change to improve.

01

Design a chassis around the system

A chassis is not a decorated plate. It locates every component, carries loads into the wheels, protects wiring, and leaves room for hands and tools.

Annotated top and side views of a robot chassis showing wheel axes, centered battery, controller access, sensor cone, cable passage, wheelbase, and ground clearance
Design relationships before the outline. Start with measured parts and the jobs they must do. The footprint constraint is only one requirement; access, clearance, sight lines, and load placement decide whether the assembled robot is usable.Original ClassroomOS instructional diagram.

Learn

Start with the wheels, motors, battery, controller, sensor sight lines, fasteners, and cable bends. Measure real parts; online dimensions may omit plugs and wires.

Predict

Sketch top, side, and front views. Mark the center of mass and predict which component will be hardest to service after assembly.

Build

Model a plate within 150 × 150 mm. Add axle clearance, repeated mounting holes, wire passages, and a replaceable sensor bracket.

Test

Print the drawing at 100%, place the real parts on it, and turn the planned wheels. Revise collisions before exporting.

Submit

  • Three-view sketch with dimensions
  • 100% paper fit-check photograph
  • Editable CAD link and exported mesh
  • One collision or access problem you corrected

Before moving on

Another team must be able to identify front, wheel axes, sensor view, battery access, and attachment method without asking the designer.

Build foundational CAD skills
02

Turn the model into a print plan

Slicing is an engineering decision: orientation changes strength, time, supports, surface finish, and dimensional accuracy.

Comparison of a robot bracket printed flat, standing on edge, and tilted with supports, with benefits and risks labeled
Orientation is a tradeoff, not a checkbox. Flat, edge, and supported orientations move layer seams, change hole quality, and expose different surfaces to support marks. Inspect the actual layer preview before approving the print.Original ClassroomOS instructional diagram.

Learn

Walls make a shell; infill supports it. Layers bond less strongly across Z than material runs within a layer. Holes and clips need printer-specific tolerance tests.

Predict

Circle the face that belongs on the bed. Mark overhangs, bridges, load paths, critical holes, and support-removal access.

Slice

Import at the intended units. Confirm the bounding box, inspect layer preview, estimate material/time, and save the approved profile.

Queue

Name files consistently. Batch small tests before full chassis parts. Record printer, material, profile, owner, and status.

Submit

  • Slicer screenshot showing dimensions and orientation
  • Predicted failure and prevention
  • Material/time estimate
  • Queue card with file version

Safety gate

Teacher approves the file and printer profile. Students do not reach into a moving or hot printer. Ventilation and material rules follow the manufacturer and school procedure.

Open the full 3D Printing Lab
03

Prototype a mount with a 3D pen

A 3D pen is a hand-controlled extrusion tool. Use it to answer a fit or structure question quickly—not to imitate the final print without a test purpose.

Butt seam, lap joint, and triangular gusset made with a 3D pen compared under a sideways load
Put plastic across the load path. A lap increases bonded area; a triangular gusset redirects bending force into two members. Thickening the same narrow butt seam does much less.Original ClassroomOS instructional diagram.

Prepare

Use the correct filament and temperature. Work on a heat-safe surface with eye protection. Keep fingers away from the nozzle and fresh plastic.

Form

Trace a full-size template, build several thin passes, turn corners gradually, and let each section cool before loading it.

Reinforce

Increase bonded area with lap joints. Add ribs or triangular gussets across bending corners instead of filling every space.

Fit-test

Mount the actual sensor, check its view and cable bend, then shake and push gently in the direction it will be loaded.

Build brief

  • Hold one sensor at its intended angle
  • Attach and remove without damaging the chassis
  • Keep the cable and sensor view clear
  • Survive three gentle load tests

Record

Photograph the template, first fit, failure point, and revised mount. Label where force entered and where the first version bent or separated.

04

Trade speed for useful force

Gears, levers, pulleys, and wheel-and-axle systems do not create energy. They exchange distance or speed for force or torque.

Comparison of a 3:1 spur gear reduction, a lever linkage arm, and a belt-and-pulley drive trading speed or travel for force
Mechanisms exchange speed or travel for force. Spur gears multiply torque at the axle, levers turn small rotation into lifting arcs, and belts transfer motion across the chassis when a motor cannot sit right at the wheel.Original ClassroomOS instructional diagram.

Observe

Test a lever, pulley, and two gear pairs. Measure input movement, output movement, and the load each arrangement can move.

Calculate

For a simple gear pair, ratio = driven teeth ÷ driver teeth. Larger ratio gives more ideal output torque and less output speed.

Choose

Write the robot’s problem first: stalled wheel, weak lift, excessive speed, or insufficient travel. Then choose a mechanism.

Sketch

Show driver, driven member, shaft supports, direction of motion, attachment, clearance, and how the robot will be serviced.

Submit

  • Station data for three mechanisms
  • Ratio calculation with units
  • Annotated robot modification sketch
  • Tradeoff statement: “We gain ___ but give up ___.”

Deepen the model

Ideal ratios ignore friction, gear deformation, motor limits, and poor alignment. Test the assembled mechanism under a known load.

Open Mechanisms and Gear Systems
05

Build controlled motion with servos

A standard hobby servo moves toward a commanded angle; a DC motor normally spins continuously. Choose based on the motion the mechanism needs.

Labeled pan-tilt servo mechanism showing horizontal and vertical axes, sensor, service loop, power checks, limits, and load moment
The shaft positions; the structure supports. Center horns before assembly, provide a cable service loop, test mechanical limits unloaded, and remember that torque demand rises with both force and distance from the shaft.Original ClassroomOS instructional diagram.

Wire safely

Confirm signal, supply, and ground. Share ground with the controller. Use an adequate separate low-voltage supply when the servo current exceeds the board’s safe capacity.

Find limits

Test the servo unloaded. Sweep slowly toward the mechanism limits; stop before binding, buzzing, or collision.

Attach

Center the servo before installing the horn. Support loads with structure and bearings rather than asking the output shaft to carry every side load.

Program

Name safe positions, move in small steps, and test one axis at a time before coordinating pan/tilt or two gripper fingers.

Choose a build

  • Pan/tilt mount: two perpendicular axes and clear cable travel
  • Gripper: symmetric fingers, hard stops, and compliant contact pads
  • For either: manual disconnect, safe angle range, and removable mount

Prove it

Demonstrate three named positions repeatedly. Record commanded and observed angles, any jitter, supply arrangement, and one mechanical limit.

Learn servo wiring and output safety
06

Integrate without creating a mystery

A full robot should not be the first test. Prove power, controller, sensor, drive, and mechanism separately, then add one subsystem at a time.

Six staged bring-up gates paired with a fault-isolation loop that unplugs the newest subsystem when a test fails
Prove one layer before adding the next. Staged bring-up keeps faults small: when Gate N fails, unplug the newest subsystem and confirm Gate N−1 still passes before hunting through the whole robot.Original ClassroomOS instructional diagram.

Inspect

Deburr parts, test fasteners, check polarity, strain-relieve wires, protect moving parts, and keep the power switch reachable.

Power

With wheels raised safely, verify supply voltage and current path. Power logic before high-load motion when the system allows it.

Integrate

Add one subsystem, run its known test, and log the result. If behavior changes, the last connection narrows the search.

Show

Demonstrate the requirement, a measured result, a revision, and the next engineering question—not just that the robot moves.

Showcase protocol

  • 30 seconds: task and requirement
  • 60 seconds: controlled demonstration
  • 30 seconds: evidence and revision
  • 30 seconds: audience question and next step

Integration log

For every subsystem, record test condition, prediction, observation, pass/fail criterion, and next action. A failed test with good evidence is useful engineering.

Review the engineering design loop
07

Design the part that meets the world

An end-effector succeeds at a specific interaction. Define the object, start line, allowed contact, mounting interface, and success test before drawing the tool.

Pusher, scoop, and two-finger gripper compared while interacting with a forty millimeter ping-pong ball
Choose the simplest tool that controls the task. A pusher tolerates alignment error, a scoop supports from below, and a gripper controls the ball after contact but adds force and positioning requirements.Original ClassroomOS instructional diagram.

Define

From 100 mm away, move a standard 40 mm ping-pong ball across a marked goal line or lift and release it in a target area.

Choose

A pusher is simple and tolerant. A scoop supports from below. A gripper controls the object but needs alignment, force, and opening range.

Interface

Measure the robot’s mounting holes, safe envelope, actuator travel, and cable route. Use a removable adapter rather than redesigning the chassis.

Iterate

Run three trials from the same line. Record success rate and failure mode. Change only one variable before the next three trials.

Design requirements

  • Mounts without permanent chassis damage
  • Stays within the robot’s safe motion envelope
  • Does not crush or puncture the object
  • Completes at least two of three controlled trials

Evidence

Submit an interface drawing, side-view reach envelope, fabrication file or template, three-trial table, and before/after photograph of the revision.

Explore reach, joints, and end-effectors
08

Make the engineering visible

Documentation lets another person understand, test, repair, and improve the robot. Photograph relationships, label interfaces, and connect claims to evidence.

Annotated engineering evidence board combining multi-view photographs with scale ruler, power and signal flow diagram, and three-trial data table
Make every engineering decision inspectable. Pair labeled views and a scale bar with power/signal diagrams and three-trial data so another team can reproduce, repair, or improve the robot without guessing.Original ClassroomOS instructional diagram.

Photograph

Use even light and a plain background. Capture full robot, top view, side view, underside, controller, sensors, drive, and end-effector. Include a ruler where scale matters.

Label

Use arrows that end on the exact component. Name the part and its job. Show power flow, signal flow, motion, front, and moving hazards.

Explain

Write task, requirement, design choice, test evidence, problem, revision, result, and next improvement. Avoid “it worked” without a condition or measurement.

Package

Submit editable CAD/code, exported files, labeled photographs, parts list, test table, summary, and credits for designs or code you adapted.

Final evidence board

  • One hero photograph and four labeled detail views
  • Parts and materials list
  • Annotated system diagram
  • Requirement-and-result table
  • One-paragraph engineering summary

Quality check

Ask a classmate who did not build the robot to point to the power source, controller, inputs, outputs, drive system, and tool—and explain one test result using only your board.