Can one motor lift a heavy crate without whipping it upward? Change two gears, predict what the hoist will do, then run a test. Every tooth you add changes the trade between turning force and speed.
Mechanical advantageGear ratiosTorque vs speedIndustrial lift lab
Tune the driver, driven, and crate load. Predict the outcome, then engage the motor to see whether the transmission stalls, lifts steadily, or triggers the overspeed stop.
System ready
1 Choose a setup2 Predict the result3 Engage and explain
Golden rule monitorRight now the system is balanced. Change the tooth counts and the live gauges will show how power shifts between speed and torque.
Load challenge500 kg crate on a 0.18 m winch drum
Build a reduction gear if the motor keeps stalling. Build a faster ratio only if you can still lift the crate without overspeeding the winch.Torque and speed balanced
Configuration
Start with a setup, then adjust any slider.
Smaller driver gears increase the ratio when they power a larger output gear.
Larger driven gears boost torque but slow the output shaft and winch.
Heavier crates require more output torque. If your ratio is too aggressive toward speed, the motor will stall.
Balance meter
VelocityTorque
Output torque1.29x
Output speed0.71x
Live ratio math
28 ÷ 20 = 1.40 : 1
Gear ratio = Teeth out / Teeth in
Output torque = Input torque × ratio × efficiency
Output speed = Input speed ÷ ratio
This model assumes 92% gear efficiency.
Select a prediction, then engage the motor.
Why this works
The lab uses a real ratio relationship. If the output gear has more teeth, it turns more slowly and gains torque. If the input gear is larger than the output gear, the winch gets faster but weaker.
A ratio above 1.00 : 1 is a reduction. That favors force over speed.
A ratio below 1.00 : 1 is a speed-up train. That favors rpm over lifting power.
If the output torque is lower than the required drum torque, the motor stalls and the crate stays put.
If the winch rpm climbs too high, the crate lifts unsafely fast and the system fails even if the torque is sufficient.
Output torque541 Nm Turning force available at the driven gear after the ratio and efficiency are applied. Required torque883 Nm The drum needs this much torque to lift the crate against gravity. Output speed86 rpm This exercise limits the winch to 52 rpm. Real safe speeds depend on the whole hoist design. Mechanical verdictUndersized The motor is currently short on torque. Increase the reduction ratio to gain lifting force.
What gears actually do
Gears do not create energy out of nowhere. They redistribute it. A small driver gear pushing a larger driven gear makes the output spin more slowly, but with greater torque. Reverse that pairing and the system spins faster, but the lifting force drops. That trade is the heart of mechanical advantage.
Driver gear The motor gear is the input. Its tooth count sets how much leverage it has over the next gear. Driven gear The output gear receives motion. A larger driven gear increases torque and lowers rpm. Opposite rotation Two meshed gears always rotate in opposite directions. The lab visualizes that sign flip directly. Mechanical advantage A reduction trades speed for torque. Friction uses some of that gain, so a ratio only slightly above 1:1 may still deliver less torque than the motor.
Design sequence
Machine design is usually a loop: define the job, estimate the force, choose a mechanism, and check the trade-offs. The same loop is happening inside this lesson.
1. Estimate the load Start by asking how much force the machine needs to move the object at all. 2. Choose the ratio Match the gear sizes so the output shaft has the right balance of torque and rpm. 3. Check the motion Even a strong design can fail if it moves too fast for the task or for the material being handled. 4. Retune the system If the machine stalls or overspeeds, adjust the ratio and test again until the mechanism matches the job.
Try a second mission
Once you lift the 500 kg crate, set the load to 900 kg. Keep the same motor and 52 rpm limit. Find a successful design and use the readouts to explain why it works.
Record your design What are the driver and driven tooth counts? Calculate the ratio before reading the live result. Prove that it lifts Compare output torque with required torque. How much torque is left over after overcoming the load? Check the speed Compare output rpm with the exercise limit. Would reversing these two gears improve the hoist? Explain the trade Describe what happened to speed when you increased lifting torque. How does the 92% efficiency assumption affect the output?
Fabricate your gears: 3D Print in Forge
Ready to test real gear meshing on the physical workbench? Open Forge to generate a 3D printable involute gear pair with an exact mounting peg board spaced to the gears' real centre distance. Adjust backlash, tooth counts, and module live, and export the STL plate ready for the MakerBot.