πŸ“‘ Wireless Mics & RF Coordination

A wireless mic is a tiny radio station. Put eight of them on one stage and they can wreck each other, even when every one is on its own channel. Learn why, then place up to eight mics in the spectrum without a single collision.

Live tool: the 8-mic coordinator

Each teal bar is a mic's carrier. Every orange tick is a third-order intermodulation product the carriers create when they mix inside a receiver (more on that below). If a tick lands inside a mic's channel, that mic hears hiss, bursts or dropouts, and the bar turns red. Drag a bar, use the arrow keys, or press Auto-coordinate.

4
0.25 MHz
12 MHz
12Products
0Collisions
0 MHzSpan used

    The TV lineups are made up for practice. A real venue uses the FCC's lookup or the maker's planning software (such as Shure Wireless Workbench) with the real stations in its area.

    1 Β· The link is just a radio wave

    The bodypack turns your voice into a radio signal on a carrier frequency. The receiver tunes to that one frequency and turns the wave back into audio. Frequency and wavelength are tied together by the speed of light:

    Ξ» = c Γ· f   Β·   c β‰ˆ 300 000 000 m/s

    An antenna works best when it is about a quarter of a wavelength long. That's why a bodypack's little whip is only about 15 cm: it is tuned to UHF.

    Wireless mics are FM or digital radio. Your voice rides on the carrier, but the carrier's frequency is what you set and what other mics must avoid.

    Wavelength calculator

    500 MHz
    0.60 mWavelength
    15 cmQuarter-wave
    ch 20US TV channel

    UHF mics live in the TV band. Each US TV channel is 6 MHz wide, and channels 14–36 cover 470–608 MHz.

    2 Β· Why different channels still collide

    A receiver's first amplifier isn't perfectly straight. Real circuits bend signals slightly, so the output includes a cubic term: y = a₁x + aβ‚‚xΒ² + a₃xΒ³. Feed in two carriers at f₁ and fβ‚‚ and the cubic term makes new frequencies you never transmitted:

    2f₁ βˆ’ fβ‚‚  Β·  2fβ‚‚ βˆ’ f₁  Β·  f₁ + fβ‚‚ βˆ’ f₃

    Example: mics on 501.0 and 500.5 MHz make 2(501.0) βˆ’ 500.5 = 501.5 MHz. If a third mic is parked on 501.5, it is now being jammed by its neighbours. Evenly spaced channels are the worst plan, because every product lands exactly on the next carrier.

    Same maths as audio distortion: clip a signal and its harmonics appear; play two tones into a clipping preamp and intermod shows up there too (see gain staging and the Fourier series lesson).

    The problem grows faster than the rig

    8

    3 Β· The cleanest layout is a Golomb ruler

    A product 2f₁ βˆ’ fβ‚‚ hits a carrier f₃ only when f₁ βˆ’ f₃ = f₃ βˆ’ fβ‚‚, two gaps that are equal. A three-carrier product f₁ + fβ‚‚ βˆ’ f₃ hits fβ‚„ only when two pairs of carriers have the same sum, which again means two equal gaps. So the perfect plan is a set of frequencies in which every gap between any two mics is different. Mathematicians call that a Golomb ruler.

    Shortest possible rulers have known lengths. Multiply each by your receiver clearance to get the minimum spectrum an ideal plan needs. Change the clearance slider above and the table follows.

    MicsMarks (Γ— clearance)Min. spanTV channels

    Real coordination is messier: it also checks 5th-order products, intermod made between transmitters, and each receiver's measured selectivity. But the ruler idea is why 8 mics need more than the "8 slots" you'd count by eye: the span grows roughly with the square of the mic count.

    4 Β· Where the antennas go

    Frequency planning gets the channels right. Antenna placement keeps the signal strong enough to use them. At UHF the wave is blocked by people, scenery and metal, so give each receiver antenna a clear line of sight to the stage.

    STAGE metal truss and scenery (reflects and absorbs radio) FRONT OF HOUSE set piece Performer A bodypack on clear line of sight Performer B behind the set piece antenna pair mounted high, facing the stage low-loss coax receiver rack in the booth KEY Clear path strong, steady signal Blocked path weak signal, dropouts Why it fails Bodies, metal and walls absorb or bounce UHF. Move the antennas, not the mic.

    Diversity receivers

    Each receiver has two antennas and always uses the one with the stronger signal. A radio wave bounces off walls and meets itself, so at some spots the signal cancels out. That is a dropout, and a second antenna a few wavelengths away is rarely in the same dead spot.

    Share the antennas

    Eight receivers don't need sixteen antennas on the wall. An antenna distribution box splits two good antennas to every receiver, so every mic hears the same strong signal and the rack stays tidy.

    πŸ“· Meet the real gear

    Click a photo to enlarge it. Find the mic's end of the radio link, then the receiver's end.

    Ear-mounted miniature headset microphone connected to a bodypack transmitter
    Transmitter end: headset and bodypackThe bodypack's short antenna is the radio station. Its frequency is set from a menu, and every other bodypack on the stage must be set to a different, coordinated one. CC0 public-domain dedication Β· Wikimedia Commons β†—
    Rack containing multiple professional wireless microphone receivers with antennas and channel labels
    Receiver end: a rack of channelsOne receiver per mic, each labelled and tuned to its partner. Notice the antennas: they decide how reliably the link works, so they get a clear view of the stage. CC0 public-domain dedication Β· Wikimedia Commons β†—