First successful moving part · one printer test, one spinner

Make a disc that turns inside its cup.

Start by changing the gap in the editable scene below. Then print a small clearance comb, measure which slots actually open on your printer, and use that evidence to build a captured spinner. The six hour spiral cone is an optional extension after the disc turns.

01 · Explore

Where must air remain?

Point to the radial gap beside the disc and the layer gaps above and below it. A gap in the model does not guarantee a gap in the sliced toolpath.

Try the editable scene
02 · Calibrate

Test your printer

Print the comb flat with supports off. Record the smallest slot that is visibly open and flexes freely; inspect the slicer preview if none survive.

Make the clearance comb
03 · Make it move

Build the spinner

Model two separate solids, check all three gaps in the slicer preview, and print with supports off. Show that the disc turns while it stays captured.

Make the captured spinner

Choose your level: Younger makers can predict, adjust the browser model, and compare teacher-printed samples. Middle grades can measure the comb and model the cup in Tinkercad. Older students can construct the Blender cross-section, revise from print evidence, and explain the geometry.

Predict the fit before printing

The same outer ring behaves differently as the radial gap changes.

Three captured rings with too-tight, working, and too-loose gaps; the inner moving part gets smaller from left to right.
A gap that closes after printing fuses the parts; an oversized gap rattles. Print a clearance comb with your printer and filament to choose a working value. Original ClassroomOS teaching diagram.
A blue 3D printed fidget cube standing on a build plate; narrow spaces separate its linked moving sections and hinges.
In this real print-in-place fidget cube, narrow gaps keep the linked sections free to move. The photo shows the visible result, not a measured clearance value. Photo by Gary C Martin via Wikimedia Commons, CC BY 2.0; resized to WebP.
Core build guide: comb and captured spinner

Use this production path after the editable scene. Finish when the disc turns freely inside its cup and you can explain the three measured gaps.

Three builds, one idea

Every fidget you print is the same trick.

A 3D printer places lines of plastic layer by layer. It has no idea what a hinge is. If the deposited lines touch, two intended parts can fuse. Your job is to design a gap, confirm that the slicer preserves it, and test whether the printed parts really move.

The first two builds complete the core lesson. The spiral cone adds twist, Boolean construction, and a long print for makers ready to extend it.

BUILD 01

Clearance comb

Six slots, from 0.15 mm to 0.5 mm, cut in one Boolean. Prints in ten minutes and tells you the one number the rest of this lesson depends on.

Boolean · 10 min print
BUILD 02

Captured spinner

A disc that spins inside a cup, printed as one piece. You draw the clearance straight into a cross-section and revolve it with the Screw modifier.

Screw revolve · 40 min print
OPTIONAL EXTENSION

Spiral cone fidget

Apply the measured fit to a twisted-star cone and its sleeve. Push the tip and the cone spins down through the sleeve.

Array + Simple Deform + Boolean · 6 hr print

Pick your tool

TINKERCAD

Free, in a browser, already in millimetres

Adds and subtracts shapes from a fixed library — which is all Builds 01 and 02 need, and it will never let you get the units wrong. The spiral cone needs its Codeblocks mode for the twist, because the editor cannot twist a shape.

BLENDER

Installed, and it can sweep any profile

Revolves a cross-section into a solid and twists any shape smoothly, so all three builds happen in one place. The price is that you have to tell it you are working in millimetres.

Every build below carries both paths — pick a tab and follow it. The design numbers never change; only the clicks do.

Why the third build needs a different approachTinkercad is a constructive solid geometry modeller: every object is primitives added together or subtracted. Blender is a mesh modeller, where any shape can be bent and twisted. The spiral cone's fins are a star shape twisted as it rises — in Blender that is one modifier, and in Tinkercad it has to be approximated by a stack of thin star slices placed by a loop.
Bring your printer's numbersEverything here is written for a 0.4 mm nozzle at 0.2 mm layers in PLA — the classroom default. If your machine differs, the labs below recompute for it; change the nozzle and layer dropdowns and the safe gaps move with them.
CheckpointYou can explain, in one sentence, why a printed hinge does not need to be assembled — and what physically happens if its gap is too small.

The one measurement that matters

Clearance has two different sizes.

Designers say "leave 0.4 mm clearance" as if a gap were a gap. It is not. A gap between two walls standing side by side is a slot the nozzle has to drive around. A gap between one part and the part above it is a ceiling the next layer has to fly across. Those two situations fail in opposite directions, so they get different numbers.

Clearance Lab

A cross-section of two neighbouring walls, drawn bead by bead

CROSS-SECTION
0.4 mm

Each rounded block is one extruded bead. A bead is always a little wider than the nozzle that made it — that spread is what welds parts together.

      XY starting point: nozzle widthTry 0.4 mm for a 0.4 mm nozzle, then inspect the sliced outlines and print a test. Slicer settings and plastic spread can change the outcome.
      Z starting point: layer heightTry one 0.2 mm layer of air at 0.2 mm layers, then check the preview and physical print. Bridging, first-layer spread, and cooling can still fuse or sag.
      Bigger is not automatically betterA very large ceiling gap may leave the next layer unsupported. Adjust one dimension at a time and compare the resulting print.
      Why inspect the toolpathA slicer draws extrusion paths from your model. Thin model gaps can disappear, survive, or be changed by gap-fill and extrusion settings. The layer preview shows what the printer is actually instructed to deposit.

      Build 01 · measure your own machine

      Stop guessing. Print the comb.

      Nozzle, filament, slicer settings, and first-layer squish affect the real minimum clearance. This open-slot comb is a quick screening test: it tells you which narrow slots your printer can preserve. A captured spinner may need a larger gap because its parts have more contact area and a hidden ceiling.

      Blender path

      1. Set Blender to millimetres

        Open Properties Editor → Scene → Units. Unit System: Metric, Unit Scale: 0.001, Length: Millimeters. Now typing 50 into a dimension field means 50 mm, and your STL will export at the size you think it is.

        Units
      2. Add the plate

        Shift+A → Mesh → Cube. In the N sidebar set Dimensions to 50 x 24 x 3 mm and Location Z to 1.5 mm so it sits on the ground plane. Then Ctrl+A → Scale.

        Plate
      3. Add six cutters

        Add a Cube with Dimensions 0.15 x 16 x 5 mm at Location (−20, −4, 1.5). Shift+D to duplicate it five times, moving each to X = −12, −4, 4, 12, 20 and setting its X dimension to 0.2, 0.25, 0.3, 0.4, and 0.5 mm. Apply scale to every one of them.

        Cutters
      4. Join, then cut once

        Select all six cutters, Ctrl+J to join them into a single object. Select the plate, then Properties Editor → Modifiers → Add Modifier → Generate → Boolean, Operation: Difference, Object: the joined cutters. One modifier, six slots.

        Boolean
      5. Print it flat, no supports

        Export STL, slice at 0.2 mm layers with supports off, and print. Hold it to a light: find the narrowest slot that is open and whose finger flexes freely. Record it as this setup's open-slot result, then verify the enclosed spinner separately.

        Measure

      Tinkercad path

      1. Start with a Ruler

        New 3D design, then drag the Ruler out of the right-hand toolbar onto the workplane. Every shape you select now shows editable width, length, height, and position boxes — all in millimetres, which is what makes Tinkercad immune to the unit-scale trap.

        Ruler
      2. Drop the plate

        Drag a Box onto the workplane and type its size into the dimension boxes: 50 wide, 24 long, 3 high.

        Plate
      3. Make one slot

        Drag a second Box, size it 0.15 x 16 x 5, and click Hole in the Inspector — it turns transparent. Slide it so it crosses the front edge of the plate and stops 8 mm short of the back, leaving a spine.

        Hole
      4. Duplicate across the plate

        Ctrl+D five times. Set each copy 8 mm further along X and change only its width: 0.2, 0.25, 0.3, 0.4, 0.5. At 0.15 mm the hole is thinner than the line drawn on screen — trust the number box, not your eyes.

        Duplicate
      5. Group once, cut six times

        Select everything (Ctrl+A) and press Ctrl+G. In Tinkercad, Group is the Boolean: solids merge, holes subtract, all in one step.

        Group
      6. Export and print

        Export → .STL, slice at 0.2 mm with supports off, and print flat. Record the narrowest slot that is open and flexes freely. Use it to inform, then physically test, your captured-spinner design.

        Export
      Write the result on the printMark the narrowest freely moving slot, printer, filament, and settings on or beside the comb. It is evidence for this setup, not a universal minimum for every print-in-place geometry.
      CheckpointYour comb has slots that visibly exist at the wide end and visibly vanished at the narrow end. If all six slots opened, your printer is unusually well tuned; if none did, re-check that supports were off and that the slots survived into the slicer preview.
      Every slot printed solid?
      • Look at the slicer preview, not the model. If the preview shows one solid outline, the slots never made it to the toolpath — the gaps are smaller than one extrusion width.
      • Check that you applied scale (Ctrl+A → Scale) before the Boolean. An unapplied scale silently resizes the cutters.
      • Confirm the plate really is 50 mm long in the slicer. If it arrived 0.05 mm long, your unit scale is wrong — see Build 03's export step.

      Build 02 · parts inside parts

      Draw the gap into the cross-section.

      Round parts are not modelled by pushing vertices around in 3D. You draw a flat outline — the cross-section of the part, measured from the axis outward — and spin it. In Blender that is the Screw modifier. Learn it on a disc captured inside a cup, printed as one piece, spinning on the first try — the same nested-parts idea the spiral cone scales up to two full-size pieces.

      Here is the whole design. Read it as a slice through the middle: the left edge is the axis, and every measurement is a radius.

      Cross-section of a captured disc inside a cup, showing a 0.4 mm radial gap and 0.2 mm gaps above and below the disc.
      The clearance is not a setting — it is geometryNothing in the slicer will add these gaps for you. The 0.4 mm outside the disc, the 0.2 mm under it, and the 0.2 mm over it are drawn into the profile before anything is revolved.

      Blender path

      Type these into the N sidebar with one vertex selected. X is the radius, Y stays 0, Z is the height.
      PartX (radius)Z (height)What it is
      Cup00Centre of the base, on the bed
      Cup200Outside edge of the base
      Cup2010Top of the outer wall
      Cup13.610Lip — narrower than the disc, so it cannot escape
      Cup16.67.0Ceiling of the groove, at 45° so it self-supports
      Cup16.62.6Outer wall of the groove
      Cup02.6Floor the disc spins on
      Disc82.8Finger hole, 0.2 mm above the floor
      Disc16.22.8Rim, 0.4 mm inside the groove wall
      Disc16.26.8Top of the rim, 0.2 mm under the groove ceiling
      Disc86.8Back to the finger hole
      1. Make an outline, not a face

        Add a Plane, Tab into Edit Mode, select all, then X → Only Faces. You are left with four vertices joined by four edges — a closed outline the Screw modifier can sweep into a surface.

        Outline
      2. Place the vertices

        Select one vertex at a time and type its X and Z from the table into the N sidebar. For the cup, select an edge and press E to extrude the extra vertices until all seven are placed and the loop closes.

        Profile
      3. Revolve it

        Properties Editor → Modifiers → Add Modifier → Generate → Screw. Axis: Z, Angle: 360°, Screw: 0 mm, Steps: 64, and turn on Merge Vertices so the seam closes into a watertight surface.

        Screw
      4. Build the disc the same way

        Four vertices, same modifier, same settings. Leave both objects in the scene, exactly where they sit. You are not going to cut anything — the air between them is already the design.

        Disc
      5. Print without touching the slicer's support button

        Supports off. The disc's first layer prints across 0.2 mm of air over the cup's floor, lands, and cools without bonding. That is the whole trick.

        Print

      Tinkercad path

      Tinkercad thinks in diameters and heights above the workplane, so the same design reads like this.
      ShapeSize (mm)Height above workplaneSolid or hole
      CylinderØ40 x 10 high0Solid — the blank
      CylinderØ33.2 x 4.4 high2.6Hole — the groove
      ConeØ33.2 x 16.6 high7.0Hole — the 45° ceiling
      CylinderØ32.4 x 4 high2.8Solid — the disc
      CylinderØ16 x 4 high2.8Hole — the finger hole
      1. Raise the side count first

        Drag in a Cylinder and set Sides to 64 in the Inspector before you size it. Tinkercad's default 20-sided cylinder is a visible polygon, and a polygonal disc grinds instead of spinning.

        Sides
      2. Blank, then groove

        Size the cylinder Ø40 x 10. Add a second cylinder Ø33.2 x 4.4, click Hole, use Align to centre it on the blank, and raise it 2.6 mm above the workplane.

        Groove
      3. Cut the ceiling with a cone

        Add a Cone, size it Ø33.2 x 16.6 high, make it a Hole, centre it, and raise it 7.0 mm. A cone whose radius equals its height has 45° sides — so this one cut gives you a self-supporting ceiling and leaves a Ø27.2 lip at the top.

        Chamfer
      4. Group the cup — and only the cup

        Select the blank and its two holes, then Ctrl+G. Do this before the disc exists. If the disc is in the selection when those holes fire, they will eat straight through it.

        Group
      5. Build the disc separately

        Cylinder Ø32.4 x 4 with a Ø16 hole through the middle, grouped together, raised 2.8 mm, then aligned to the cup's centre. Leave it as its own object so you can still nudge it.

        Disc
      6. Check the three gaps by arithmetic

        Ø33.2 − Ø32.4 leaves 0.4 mm all the way around. 2.8 − 2.6 leaves 0.2 mm underneath. 7.0 − 6.8 leaves 0.2 mm above. Tinkercad will not warn you about any of these — the numbers are the only check you get.

        Verify
      Why the ceiling is chamfered at 45°A flat ledge over the disc would be an unsupported horizontal roof. Sloping it from r16.6 to r13.6 over 3 mm of height makes every layer land on the one below at exactly 45° — the steepest angle a printer can hold without support. Self-supporting geometry is designed, not fixed later.
      CheckpointYour cup and disc are two separate objects that never touch, and you can state the three gaps out loud: 0.4 mm at the side, 0.2 mm below, 0.2 mm above.

      Want to check your numbers, or print one without modelling it? The same cup and disc are a part in Forge: change the sizes and it checks every gap against your class clearance. Forge also has a captive wheel & axle, a 3-in-1 rolling creature tool, a fidget spinner and a print-in-place hinge built on the same trick.

      First print · close the evidence loop

      Slice, print, observe, revise.

      1. Inspect the sliced layers

        Check the cup and disc at the bottom, middle, and lip. They must remain separate outlines. Check that the finger hole and 0.2 mm floor and ceiling spaces remain open. If the slicer fills a gap, revise the model before printing.

        Preview
      2. Print with supports off

        Keep the cup flat on the bed. Verify the outer diameter in the slicer is 40 mm. Use the same material, nozzle, layer height, and first-layer setup as the comb. Keep both solids in their modeled positions.

        Print
      3. Test gently

        Once cool, hold the cup and turn the disc with a finger. It should rotate while the lip keeps it in the cup. If it sticks, record where; inspect for a first-layer weld before increasing every gap.

        Observe

      Record your fit decision

      Keep the printer setup with your measurements so you can repeat or compare the test. This record stays in this browser.

      Core finish lineShow the freely turning disc, identify the air gaps in the sliced preview, and explain one choice you changed or kept based on the printed evidence.
      Optional advanced build: spiral cone, print checks and troubleshooting

      Continue here after the captured spinner works. The twisted cone has more contact area and a longer print; its clearance needs its own preview and physical test.

      Design it before you model it

      The spiral cone is two prints and one twist.

      Pick up the real fidget and you are holding two parts. Inner is a cone carved into a nine-fin star that twists as it rises. Outer is a sleeve: the same cone with a slightly fatter copy of that twisted star cut out of it. Because both stars twist at the same rate, the cone cannot slide straight: the only path that keeps every fin inside its slot is down-and-around together, like a screw. So a straight push on the tip comes out as spin — the cone turns its way through and drops out the bottom. Feed it back in and do it again.

      Both parts are cut from one cone, so they print nested, already assembled, separated by the designed clearance. Drag the sliders to test geometric constraints such as lean, gap, and wall thickness. Then inspect the actual sliced toolpaths and make a physical test; this lab cannot predict whether the printed parts will move.

      Spiral Cone Lab

      Drag to orbit · orange is Inner, teal is Outer · every number here is a number you type into Blender

      LIVE MODEL
      9
      117°
      0.75 mm
      6 mm
      32.5 mm
      41 mm
      82 mm
      Customize in Forge →

          The three rules the lab is checking

          ∠

          Can it hold itself up?

          Lean = atan(reach × twist rate)

          117° through an 82 mm sleeve is 1.43° per millimetre. At the fin tips, 32.5 mm out, that leans the faces 38.5° from vertical — inside the 45° rule, so every layer lands on the one below. Twist harder or reach further and the tips cross 45°.

          ↔

          Will the two pieces separate?

          Air = clearance × cos(lean)

          The clearance is measured flat, across the slice, but the fin faces lean. So 0.75 mm of clearance leaves only 0.59 mm of real air at the tips — about one and a half beads. That is why the reference pair uses 0.75 mm, not the 0.4 mm your comb passed.

          ▮

          Will the sleeve hold together?

          Fins in, collar under

          Fin reach stops 8 mm short of the base, so the bottom 23 mm of the sleeve is a solid collar that ties its nine fingers together. And between the slots, near the core, each finger still needs two beads of plastic — too many or too wide fins and the fingers vanish.

          Twist rate is your spinTwist ÷ sleeve height is the twist rate: how many degrees the cone turns for every millimetre it drops: 117° ÷ 82 mm = 1.43°/mm. Pushed all the way through, the 110 mm cone turns about 157°. Zero twist still works — the cone just slides straight out without spinning.
          CheckpointFind a setting where every verdict is green, then break exactly one of them on purpose and say which physical failure it would cause on the bed.

          Build 03 · the boss fight

          Twist a star, then split a cone with it.

          Build it the way it works. Make a star — a round core with nine fins — and twist it up the axis. Make a second star the clearance fatter everywhere and twist it exactly the same way. Keep what is inside both the cone and the first star: that is Inner. Cut the second star out of the cone: that is Outer. You can also inspect both pieces live on the MakerBot bed in Forge.

          Blender path

          1. Make the core

            Shift+A → Mesh → Cylinder. Vertices 64, Radius 11.5 mm, Depth 112 mm, Location Z 55 mm. It runs from 1 mm below the bed to 1 mm above the cone's tip, so every later cut passes cleanly through it.

            Core
          2. Add one fin

            Add a Cube and set its Dimensions to X 26.75, Y 6, Z 112 mm, Location X 19.125, Z 55. It reaches from inside the core out to 32.5 mm — the fin reach. For the round tip of the reference pair, select the two outer vertical edges and Ctrl+B bevel them by 2.9 mm with 8 segments.

            Fin
          3. Repeat it nine times

            Add an Empty at the origin and set its Rotation Z to 40° (360 ÷ 9). On the fin, Add Modifier → Generate → Array: Count 9, Relative Offset off, Object Offset on, Object: the Empty. Apply it, then Boolean Union the fins into the core and apply. Name the result Star.

            Array
          4. Build the slot star

            Repeat steps 1–3 with every number grown by the 0.75 mm clearance: core radius 12.25, fin Y 7.5, fin X 27.5 at Location X 19.5 (reach 33.25), bevel 3.65 mm. Same depth, same location. Name it Slot.

            Slot
          5. Give both stars rings to twist on

            Select Star, Tab into Edit Mode, hover a vertical edge, press Ctrl+R and type 112 before clicking — one ring every millimetre, all the way round. Do the same on Slot. A twist can only bend a mesh at its vertices; a fin with no rings in it would stay straight.

            Rings
          6. Twist them

            Add Modifier → Deform → Simple Deform, mode Twist, Axis Z, Angle 160° — the lab's 1.43°/mm over the star's 112 mm. Give Slot the identical modifier and apply both. The twist only lines up because both stars are the same height, at the same place, twisted by the same angle: change one number on one star and the cone will jam.

            Twist
          7. Make the two cones

            Add a Cone: Vertices 96, Radius 1 41 mm, Radius 2 4 mm, Depth 110 mm, Location Z 55. Add a second Cone for the sleeve: Radius 1 41, Radius 2 13.45, Depth 82, Location Z 41. Both lose 0.336 mm of radius per millimetre of height — one cone surface, cut off at two heights.

            Cones
          8. Split the cone

            On the tall cone, Add Modifier → Generate → Boolean, Solver Exact, Operation Intersect, Object Star, apply: that is Inner. On the sleeve cone, Boolean Difference with Slot, apply: that is Outer. Hide the stars and save as spiral-cone-fidget.blend.

            Boolean

          Tinkercad path

          Tinkercad's 3D editor adds and subtracts shapes from a fixed library. It can make a star and it can make a cone, but it cannot twist anything — so build the straight-fin version in the editor first (it works: the cone slides through without spinning), then use Codeblocks to stack thin star slices into a twist.

          1. Make the star

            A Cylinder Ø23, 112 tall, lowered 1 mm into the workplane. Add a Box 27 long × 6 wide × 112 tall reaching from the centre out to 32.5 mm. Duplicate it with Ctrl+D, rotate the copy 40° about the centre, then press Ctrl+D seven more times — Tinkercad repeats the rotation. Group everything: that is the Star.

            Star
          2. Make the slot star

            The same thing grown by the clearance: Cylinder Ø24.5, boxes 7.5 wide reaching to 33.25 mm. Group it: that is the Slot.

            Slot
          3. Make the cones

            Tinkercad's Cone shape takes a base radius, a top radius, and a height. Inner cone: 41 → 4, 110 tall. Sleeve cone: 41 → 13.45, 82 tall. Turn Sides up to the maximum.

            Cones
          4. Outer: cone minus slot

            Set the Slot to Hole, select it with the sleeve cone, and Group. That is Outer.

            Outer
          5. Inner: keep only the star inside the cone

            Tinkercad has no intersect, so make a mould: a Box bigger than the cone, grouped with the inner cone set as a Hole, leaves a block with a cone-shaped hollow. Set that whole mould to Hole and group it with the Star — everything outside the cone is cut away. That is Inner.

            Inner
          6. Add the twist in Codeblocks

            In Create → Codeblocks, loop i from 0 to 111. Each pass, build one 1 mm star slice (a Cylinder and nine Boxes, 1 mm tall), rotate it by 1.43 · i degrees about Z, then move it up i − 1 mm. Run the same loop for the slot star. Send both results to the 3D editor and use them in steps 4 and 5 in place of the straight stars.

            Twist
          A staircase needs more clearanceEach 1 mm slice turns 1.43°, which at the fin tips is a 0.81 mm step — bigger than the 0.75 mm clearance, so a staircase cone catches on every stair. In Tinkercad, grow the slot star by 1.0 mm instead (Ø25, boxes 8 wide, reach 33.5). Thinner slices fix it too, but 224 slices of ten shapes each is about as much as Codeblocks will put up with.
          Why the stars run past both endsA Boolean between two faces that lie exactly on top of each other — a star bottom and a cone bottom both at Z = 0 — is the most common way to get a broken mesh. Running the stars 1 mm past the bed and past the tip means every cut goes cleanly through.
          Why the fins stop short of the baseThe fins reach 32.5 mm; the base is 41 mm. Below about 23 mm the sleeve is wider than the slot, so it stays a solid collar. Above that, the slot breaks through the cone wall and the sleeve becomes nine fingers — held together only by the collar. Let the fins reach the edge and Outer prints as nine loose strips.
          The cone jams half-way through the sleeve
          • The two stars were twisted differently. They must be the same height, at the same location, with the same Simple Deform angle — check all three.
          • One star has fewer rings than the other, so it bent along different chords. Give both the same loop-cut count.
          • The slot star was made from the same numbers as the fin star. Every slot number must be grown by the clearance: core +0.75, fin width +1.5, reach +0.75.
          • If the Boolean returns garbage, run 3D-Print Toolbox → Check All on each star first. A star with holes in it cuts holes that make no sense.

          Check, export, slice

          Let Blender find the flaws first.

          Blender ships with a print checker most people never turn on. Enable it once and it will tell you, before you waste filament, whether your mesh is a real solid and whether anything on it is too thin or too steep to print.

          1. Turn on the 3D-Print Toolbox

            Edit → Preferences → Add-ons, search for "3D Print", and enable 3D Print Toolbox (older builds list it as "Mesh: 3D-Print Toolbox"). It appears as a 3D-Print tab in the N sidebar.

            Add-on
          2. Run Check All

            Set Thickness to 0.8 mm and Overhang to 45°, then press Check All. You want zero non-manifold edges and zero intersections. Anything reported gets clicked — the toolbox selects the exact faces at fault.

            Check
          3. Export the pair in millimetres

            Select Inner, File → Export → STL (.stl) with Scale 1.00 and Selection Only ticked, saved as spiral-cone-inner.stl. Do the same for Outer. Don't move either first: they share one origin, so the slicer loads them nested. Then verify: Inner reads about 65 × 65 × 110 mm and Outer 82 × 82 × 82 mm. If one arrives as a 0.08 mm speck, your scene unit scale was never set to 0.001.

            Export
          4. Choose nested or apart

            Nested: add both files to one build plate without moving them (turn off auto-arrange) and they print already assembled — the print-in-place way, and it also lets you print the pieces in two colours. Apart: lay them side by side, print, then feed the cone into the bottom of the sleeve and twist it home. Both work; nested is the one that tests your clearance.

            Plate
          5. Slice it deliberately

            0.2 mm layers, 3 walls, 15% infill, supports off, seam position Random, cooling fan 100% after the third layer, PLA at the cool end of its range. Vase mode stays off — it would delete the core and the fins.

            Slice
          6. Read the preview before you press print

            Drag the layer slider to the middle of the sleeve. You should see the star of the cone and the fingers of the sleeve as separate outlines, with a dark line of air all the way round every fin. A fin that merges into a finger means the clearance did not survive slicing — go back and widen it by 0.1 mm.

            Verify

          If you modelled in Tinkercad

          No unit trapTinkercad works in millimetres and exports millimetres, so Ø60 in the editor arrives as 60 mm in the slicer. Glance at the dimensions anyway — it costs nothing.
          Nothing to make manifoldGrouped solids and holes always come out as a closed shell, so Tinkercad cannot hand you a leaking mesh. What it also cannot do is warn you about a 51° overhang or a 0.6 mm wall. That judgement is entirely yours.
          Export everything, not the selectionThe export dialog offers the whole design or just the selected shape. Choose the whole design, or the disc sitting inside the cup gets left behind and you print half a fidget.
          Supports would destroy this printSupport material is generated wherever the slicer sees overhang — including inside the twisted slot between cone and sleeve. It would print a scaffold in the one place that must stay empty and lock the cone in solid. Design so you never need it; that is what the 45° rule bought you.
          Expect a light tackA nested pair often comes off the bed slightly stuck. Hold the sleeve, push the tip down hard once, and the cone should break free and spin through. If it needs pliers and force, your gap was too small.
          Watch the tipAbove the sleeve the cone's layers are tiny, so each one returns before the previous one cooled. Turn on minimum layer time or slow the top 20% to about 20 mm/s.
          Elephant's footSquished first layers spread outward and can weld the bottom of the fins to the sleeve's collar — the one place the two pieces sit side by side on the bed. Enable elephant-foot compensation if the cone refuses to start moving.

          Read the failure, then fix the number

          Every failure names its own cause.

          It printed as one solid cone

          The clearance never reached the toolpath. Check the slicer preview at mid-height, then grow the slot star by another 0.1 mm — remember the twist costs you the cosine of the lean at the fin tips.

          The cone jams part-way through

          The fin star and the slot star were twisted differently — different heights, locations, ring counts or angles. Rebuild the slot from the fin star's numbers plus the clearance and twist both with one identical modifier.

          The sleeve fell apart into strips

          The fins reach the outside of the base, so there is no solid collar. Pull the fin reach in until the bottom 15–25 mm of the sleeve is a full ring.

          A sleeve finger snapped

          Too many fins, or fins too wide, for that core: the fingers between the slots got thinner than two beads near the middle. Drop a fin, narrow them, or grow the core.

          Stringy chaos near the tip

          The cone's cross-section gets tiny above the sleeve, so layers stack before they cool. Enable minimum layer time, run the fan at 100%, and drop the top-section speed.

          The slicer shows a 0.06 mm object

          Scene unit scale. Set Scene → Units → Unit Scale 0.001, Length: Millimeters, re-export, and re-check the dimensions in the slicer every time.

          Tinkercad: the disc is fused to the cup

          Check the arithmetic before you blame the printer. Ø33.2 − Ø32.4 must leave 0.4 mm, and 2.8 − 2.6 must leave 0.2 mm. Tinkercad lets two solids overlap by a tenth of a millimetre without a word, and Group then welds them into one body.

          Tinkercad: the twisted cone catches on every slice

          The stair step at the fin tips is bigger than the clearance. Grow the slot star to 1.0 mm of clearance, or make the slices thinner — the step is fin reach × the slice's turn in radians.

          Blender reports non-manifold edges

          Usually the Boolean. Apply scale on both objects (Ctrl+A → Scale), switch the solver to Exact, and re-cut. Stray loose edges left over from a profile also count — select all in Edit Mode and use Mesh → Clean Up → Delete Loose.

          Only the very bottom is stuck
          • Classic elephant's foot: the first layers are squished wider than designed and bridge the gap between the fins and the collar. Enable elephant-foot compensation, or lower the bed temperature slightly.
          • Check your first-layer squish. An over-squished first layer spreads plastic 0.1–0.2 mm past where the model said it should be — enough to close most of a 0.6 mm gap.
          • Push the tip down while turning it the way the fins twist. The pieces shear apart along the twist far more easily than they separate straight down.

          Exit ticket

          Would it survive a pocket?

          1. Why must a side-by-side gap be at least one nozzle width?
          2. A fin tip sits 32.5 mm from the axis and the star twists 1.43° per millimetre. What does that tell you?
          3. Why can a Z gap be smaller than an XY gap?
          4. Why are supports forbidden on a nested spiral cone?
          5. You push the tip straight down. Why does the cone spin?

          Definition of done

          Tune the printer next →

          Take it further

          1

          Predict the spin

          Mark the tip, drop the cone through, and measure how far it turned. Twist rate × distance dropped should predict it — find out how close it gets.

          2

          Left-handed pair

          Give both stars a −160° twist. Print a left-handed and a right-handed pair and try to swap their cones.

          3

          Hex cone

          Drop both cones' Vertices from 96 to 6. The same fidget with flat facets feels completely different in the hand.