[{"title":"File:3D printing calibration build plate first layer gap.png","target":"assets/images/3d-printing/first-layer-gap.png","maxDim":1600,"format":"png","desc":"Calibration diagram showing first layer nozzle distance: too high (detached beads), optimal squish (continuous bonded sheet), and too low (furrows and transparent skin)","author":"Stemfie3D","source":"https://commons.wikimedia.org/wiki/File:3D_printing_calibration_build_plate_first_layer_gap.png","license":"CC BY-SA 4.0","licenseUrl":"https://creativecommons.org/licenses/by-sa/4.0/"},{"title":"File:3D printing calibration elephant foot.png","target":"assets/images/3d-printing/elephant-foot.png","maxDim":1600,"format":"png","desc":"Elephant foot defect diagram: downward nozzle squish and bed temperature causing initial layer perimeter expansion, with 45-degree chamfer and slicer compensation","author":"Paulo Kiefe / Stemfie3D","source":"https://commons.wikimedia.org/wiki/File:3D_printing_calibration_elephant_foot.png","license":"CC BY-SA 4.0","licenseUrl":"https://creativecommons.org/licenses/by-sa/4.0/"},{"title":"File:3D printing calibration build plate levelling.png","target":"assets/images/3d-printing/bed-leveling.png","maxDim":1600,"format":"png","desc":"Four-point build plate tramming and leveling diagram showing bed leveling thumbscrews and nozzle gap inspection","author":"Stemfie3D","source":"https://commons.wikimedia.org/wiki/File:3D_printing_calibration_build_plate_levelling.png","license":"CC BY-SA 4.0","licenseUrl":"https://creativecommons.org/licenses/by-sa/4.0/"},{"title":"File:3D printing calibration part-cooling fan airflow.png","target":"assets/images/3d-printing/cooling-fan-airflow.png","maxDim":1600,"format":"png","desc":"Part cooling fan airflow and duct placement diagram showing rapid cooling directed at freshly extruded filament below the heater block","author":"Paulo Kiefe","source":"https://commons.wikimedia.org/wiki/File:3D_printing_calibration_part-cooling_fan_airflow.png","license":"CC BY-SA 4.0","licenseUrl":"https://creativecommons.org/licenses/by-sa/4.0/"},{"title":"File:Gyroid.jpg","target":"assets/images/3d-printing/gyroid-infill.jpg","maxDim":1600,"format":"jpeg","quality":85,"desc":"Close-up photograph of 3D printed gyroid infill showing triply periodic minimal surface geometry providing isotropic load resistance without nozzle crossover collisions","author":"A7N8X","source":"https://commons.wikimedia.org/wiki/File:Gyroid.jpg","license":"CC BY-SA 4.0","licenseUrl":"https://creativecommons.org/licenses/by-sa/4.0/"},{"title":"File:Riempimenti differenti.png","target":"assets/images/3d-printing/infill-patterns.png","maxDim":1600,"format":"png","desc":"Comparison of four physical 3D printed infill patterns: rectilinear grid, triangular, honeycomb, and concentric perimeters","author":"A7N8X","source":"https://commons.wikimedia.org/wiki/File:Riempimenti_differenti.png","license":"CC BY-SA 4.0","licenseUrl":"https://creativecommons.org/licenses/by-sa/4.0/"},{"title":"File:Stampa 3d supporti albero.jpg","target":"assets/images/3d-printing/tree-supports.jpg","maxDim":1600,"format":"jpeg","quality":85,"desc":"Organic tree support columns branching up to support an overhanging printed bust, minimizing contact area and scarring on the model surface","author":"A7N8X","source":"https://commons.wikimedia.org/wiki/File:Stampa_3d_supporti_albero.jpg","license":"CC BY-SA 4.0","licenseUrl":"https://creativecommons.org/licenses/by-sa/4.0/"},{"title":"File:Stampa 3d raft.jpg","target":"assets/images/3d-printing/raft-adhesion.jpg","maxDim":1600,"format":"jpeg","quality":85,"desc":"Part printed on a multi-layer sacrificial raft bed-adhesion structure on a heated build plate to prevent corner lifting on warpy polymers","author":"A7N8X","source":"https://commons.wikimedia.org/wiki/File:Stampa_3d_raft.jpg","license":"CC BY-SA 4.0","licenseUrl":"https://creativecommons.org/licenses/by-sa/4.0/"},{"title":"File:3D Printer - the first layer(16661915478).jpg","target":"assets/images/3d-printing/first-layer-macro.jpg","maxDim":1600,"format":"jpeg","quality":85,"desc":"Macro photograph of a 3D printer laying down the foundational first layer, showing nozzle squish, line-to-line contact, and perimeter skirt","author":"Luke Jones","source":"https://commons.wikimedia.org/wiki/File:3D_Printer_-_the_first_layer(16661915478).jpg","license":"CC BY 2.0","licenseUrl":"https://creativecommons.org/licenses/by/2.0/"},{"title":"File:3D printer nozzle extruding plastic (15425519178).jpg","target":"assets/images/3d-printing/nozzle-extruding.jpg","maxDim":1600,"format":"jpeg","quality":85,"desc":"Close-up of molten filament flowing from a 0.4 mm brass nozzle tip onto the build surface, showing hotend heat block and silicone sock","author":"David Elliott","source":"https://commons.wikimedia.org/wiki/File:3D_printer_nozzle_extruding_plastic_(15425519178).jpg","license":"CC BY 2.0","licenseUrl":"https://creativecommons.org/licenses/by/2.0/"},{"title":"File:Hotend.jpg","target":"assets/images/3d-printing/hotend-assembly.jpg","maxDim":1600,"format":"jpeg","quality":85,"desc":"Complete FDM hotend assembly showing the cooling heatsink fins, heatbreak throat tube, aluminum heater block, thermistor cartridge, and brass nozzle","author":"A7N8X","source":"https://commons.wikimedia.org/wiki/File:Hotend.jpg","license":"CC0 1.0","licenseUrl":"https://creativecommons.org/publicdomain/zero/1.0/"},{"title":"File:Create, innovate, accelerate, repeat- The formula for shaping the future (8343465).jpg","target":"assets/images/3d-printing/additive-manufacturing-lab.jpg","maxDim":1600,"format":"jpeg","quality":85,"desc":"Modern educational and military additive manufacturing laboratory with desktop FDM 3D printers, enclosures, and technicians inspecting test prints","author":"Collin Wesson / U.S. Space Force","source":"https://commons.wikimedia.org/wiki/File:Create,_innovate,_accelerate,_repeat-_The_formula_for_shaping_the_future_(8343465).jpg","license":"Public domain","licenseUrl":"https://en.wikipedia.org/wiki/Public_domain"},{"title":"File:First Print 20mm Calibration Cube (5829951780).jpg","target":"assets/images/3d-printing/calibration-cube-measurement.jpg","maxDim":1600,"format":"jpeg","quality":85,"desc":"Measuring an FDM 20 mm XYZ calibration test cube with digital vernier calipers to measure axis dimensional accuracy, hole tolerances, and step calibration","author":"syvwlch","source":"https://commons.wikimedia.org/wiki/File:First_Print_20mm_Calibration_Cube_(5829951780).jpg","license":"CC BY 2.0","licenseUrl":"https://creativecommons.org/licenses/by/2.0/"}]